General Purpose Finishing Coated Carbide Square End Mills
Available940 products
General purpose carbide square end mills are intended for milling a wide variety of common materials but are not suitable for milling hard materials like titanium or gummy materials like aluminum. Finishing end mills create a finer finish on the workpiece than roughing and roughing/finishing end mills. Carbide end mills provide excellent wear resistance and heat resistance, and they are harder than high-speed steel, cobalt, or powdered-metal end mills. These end mills have a coating that protects them from wear. Also called square-nose end mills, square end mills have a square nose and are rotated against a piece of stock to create a flat-bottomed groove with 90° inside corners in milling tasks. They are used for counterboring, side and face milling, and milling square shoulders.
2-Flute General Purpose Finishing TiAlN-Coated Fractional-Inch Carbide Square End Mills
These end mills come in standard sizes expressed in fractional inches. Two-flute end mills help maximize chip clearance. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 2 Flutes
| Loading... | ||||||
| Loading... | ||||||
| Loading... | ||||||
| Loading... | ||||||
2-Flute General Purpose Finishing TiAlN-Coated Decimal-Inch Carbide Square End Mills
These end mills come in standard sizes expressed in decimal inches. Two-flute end mills help maximize chip clearance. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 2 Flutes
| Loading... | ||||||
2-Flute General Purpose Finishing TiAlN-Coated Metric Carbide Square End Mills
These end mills come in standard sizes expressed in millimeters. Two-flute end mills help maximize chip clearance. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Metric + Center Cutting + 2 Flutes
| Loading... | ||||||
| Loading... | ||||||
3-Flute General Purpose Finishing TiAlN-Coated Carbide Square End Mills
Three-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 3 Flutes
| Loading... | ||||||
| Loading... | ||||||
Metric + Center Cutting + 3 Flutes
| Loading... | ||||||
4-Flute General Purpose Finishing TiAlN-Coated Fractional-Inch Carbide Square End Mills
These end mills come in standard sizes expressed in fractional inches. Four-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||
| Loading... | ||||||
| Loading... | ||||||
| Loading... | ||||||
| Loading... | ||||||
4-Flute General Purpose Finishing TiAlN-Coated Decimal-Inch Carbide Square End Mills
These end mills come in standard sizes expressed in decimal inches. Four-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||
4-Flute General Purpose Finishing TiAlN-Coated Metric Carbide Square End Mills
These end mills come in standard sizes expressed in millimeters. Four-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Metric + Center Cutting + 4 Flutes
| Loading... | ||||||
| Loading... | ||||||
5-Flute General Purpose Finishing TiAlN-Coated Carbide Square End Mills
Five-flutes end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 5 Flutes
| Loading... | ||||||
| Loading... | ||||||
6-Flute General Purpose Finishing TiAlN-Coated Carbide Square End Mills
Six-flute end mills allow for higher feed rates than end mills with fewer flutes and clear chips more quickly than end mills with more flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Center Cutting + 6 Flutes
| Loading... | ||||||
8-Flute General Purpose Finishing TiAlN-Coated Carbide Square End Mills
Eight-flute end mills allow for higher feed rates than end mills with fewer flutes and clear chips more quickly than end mills with more flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiAlN coating on these end mills withstands high temperatures and protects them from wear. It allows the end mills to be used at faster speeds than end mills with a bright finish, and it resists cracks and oxidation better than TiN or TiCN coatings.
Fractional Inch + Non-Center Cutting + 8 Flutes
| Loading... | ||||||
Metric + Non-Center Cutting + 8 Flutes
| Loading... | ||||||
2-Flute General Purpose Finishing TiCN-Coated Carbide Square End Mills
Two-flute end mills help maximize chip clearance. The TiCN coating on these end mills protects them from wear and is harder and more wear-resistant than a TiN coating.
Fractional Inch + Center Cutting + 2 Flutes
| Loading... | ||||||
3-Flute General Purpose Finishing TiCN-Coated Carbide Square End Mills
Three-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiCN coating on these end mills protects them from wear and is harder and more wear-resistant than a TiN coating.
Fractional Inch + Center Cutting + 3 Flutes
| Loading... | ||||||
Metric + Center Cutting + 3 Flutes
| Loading... | ||||||
4-Flute General Purpose Finishing TiCN-Coated Carbide Square End Mills
Four-flute end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiCN coating on these end mills protects them from wear and is harder and more wear-resistant than a TiN coating.
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||
5-Flute General Purpose Finishing TiCN-Coated Carbide Square End Mills
Five-flutes end mills clear chips more quickly than end mills with more flutes and allow for higher feed rates than end mills with fewer flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiCN coating on these end mills protects them from wear and is harder and more wear-resistant than a TiN coating.
Fractional Inch + Center Cutting + 5 Flutes
| Loading... | ||||||
6-Flute General Purpose Finishing TiCN-Coated Carbide Square End Mills
Six-flute end mills allow for higher feed rates than end mills with fewer flutes and clear chips more quickly than end mills with more flutes. They also typically have larger cores and are less prone to breaking than end mills with fewer flutes. The TiCN coating on these end mills protects them from wear and is harder and more wear-resistant than a TiN coating.
Fractional Inch + Center Cutting + 6 Flutes
| Loading... | ||||||
General Purpose Finishing AlCrN-Coated Carbide Square End Mills
The AlCrN coating on these end mills protects them from wear during dry, high-speed machining applications. It is harder, resists cracking and oxidization better, and performs better in high-feed applications than a TiAlN coating. It also resists high heat better than an AlTiN coating.
Metric + Center Cutting + 2 Flutes
| Loading... | ||||||
Metric + Center Cutting + 4 Flutes
| Loading... | ||||||
General Purpose Finishing Altima-Coated Carbide Square End Mills
The Altima coating on these end mills protects them from wear. It is more resistant to high heat than TiN, TiCN, and TiAlN coatings and is more wear-resistant than a standard AlTiN coating.
Fractional Inch + Center Cutting + 6 Flutes
| Loading... | ||||||
General Purpose Finishing AlTiN-Coated Carbide Square End Mills
The AlTiN coating on these end mills protects them from wear and is more resistant to high heat than TiN, TiCN, and TiAlN coatings. AlTiN-coated end mills are used for milling hard and abrasive materials.
Fractional Inch + Center Cutting
| Loading... | ||||||
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||
Fractional Inch + Center Cutting + 5 Flutes
| Loading... | ||||||
Fractional Inch + Center Cutting + 6 Flutes
| Loading... | ||||||
Fractional Inch + Center Cutting + 7 Flutes
| Loading... | ||||||
Fractional Inch + Non-Center Cutting + 5 Flutes
| Loading... | ||||||
Metric + Center Cutting + 2 Flutes
| Loading... | ||||||
Metric + Center Cutting + 3 Flutes
| Loading... | ||||||
Metric + Center Cutting + 4 Flutes
| Loading... | ||||||
Metric + Non-Center Cutting + 5 Flutes
| Loading... | ||||||
General Purpose Finishing DLC-Coated Carbide Square End Mills
The diamond-like carbon (DLC) coating on these end mills protects them from wear when milling abrasive materials such as stainless steel, ceramics, plastics, and aluminum alloys. DLC-coated end mills are a cost-effective alternative to diamond-coated end mills.
Fractional Inch + Center Cutting + 3 Flutes
| Loading... | ||||||
Fractional Inch + Non-Center Cutting + 3 Flutes
| Loading... | ||||||
Metric + Center Cutting + 3 Flutes
| Loading... | ||||||
General Purpose Finishing EXO-Coated Carbide Square End Mills
The EXO coating on these end mills is a multilayered TiAlN coating with a very smooth finish. It resists wear better than a standard TiAlN coating. EXO-coated end mills can be used at high speeds and withstand high temperatures.
Fractional Inch + Center Cutting + 5 Flutes
| Loading... | ||||||
Metric + Center Cutting + 5 Flutes
| Loading... | ||||||
General Purpose Finishing TiN-Coated Carbide Square End Mills
The TiN coating on these end mills protects them from wear and resists impact better than TiAlN and AlTiN coatings.
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||
General Purpose Finishing WXL-Coated Carbide Square End Mills
The WXL coating on these end mills protects them from wear and is designed for milling nonferrous metals and steels with a Rockwell hardness of up to 50 HRC. It is harder and has a higher oxidation temperature than a TiAlN coating.
Fractional Inch + Center Cutting + 4 Flutes
| Loading... | ||||||